<?xml version="1.0" encoding="utf-8"?>
<Spec id="630" path="\5\9\5928c509d08550fda28a67990141f6da.pdf"><Text id="89549" page="1">Type: ZSE 12 HP-PH - 40D Machine number: 06080 Order number: N-40136146 Customer: Next Pharma</Text><Text id="89551" page="2">This document has been created, reviewed and approved by:</Text><Text id="89552" page="4">This document describes the components and technical features of the pharma extrusion line ZSE 12 HP-PH - 40D.</Text><Text id="89553" page="4">The machine number 06080 is a pharma extruder type ZSE 12 HP-PH - 40D which has a screw diameter of 12 mm and a process length of 40 D (in 5D increments).</Text><Text id="89554" page="4">The ZSE 12 HP-PH is a co-rotating intermeshing twin-screw extruder, designed for small scale extrusion in a range of 50 - 2000 g/h. It can be used for applications like hot melt extrusion or melt/wet granulation. The machine is made in stainless steel design and provides a D o /D i ratio which is in line with the Leistritz Pharma machines ZSE 18, 27, 40 and 50. The base frame (made of stainless steel) is hosting the drive section, the process unit including material outlet device, cooling belt, electrical components and the interface of the control system. The heating/cooling unit can be installed on a support at the frame or can be placed separately from the extruder. The process unit (consisting of barrel and screws) has 9 zones, each of them is temperature controlled by PT100 element. The heating is done by heating cartridges and the cooling by water supplied by the heating/cooling unit. The process unit is designed as a compact barrel that can be split horizontally over the whole process length. This makes a process evaluation along the screws possible. Parts for heating and cooling of the zones are firmly embedded inside a C-profile which incorporates and tensions the process unit as well. Thus the assembly, disassembly and cleaning of the process unit can be done in a few steps. The whole process unit is covered with a stainless steel cover (=heating contact protection, not cooled). The zones are always standard configurated:</Text><Text id="89555" page="4">(E = Einfüllen / Feeding, 1 = open 0 = closed)</Text><Text id="89556" page="4">By using the inserts, the zones can be adjusted in their function (e.g. from open to closed, from open for injecting liquid). The extruder is supplied with one pair of segmented screws with a total length of 40 D. The process layout is flexible. The following equipment is connected with the extruder:</Text><Text id="89560" page="4">• RX4000 Liquid dosing Watson Marlow 120U/DV with pump head 114</Text><Text id="89562" page="4">• The extruder together with the additional (peripheral) equipment is called extrusion line.</Text><Text id="89563" page="18">A weld documentation is not part of the documentation, because there are no welds available at the extruder.</Text><Text id="89564" page="1">Date Version Description 10.02.2026 1.0 Final</Text><Text id="89566" page="2">Name Signature Date Created: Qualification/Project Engineer Leistritz Extrusionstechnik GmbH Reviewed / Approved: Qualification/Project Engineer Leistritz Extrusionstechnik GmbH</Text><Text id="89569" page="4">Zone 9 Zone 8 Zone 7 Zone 6 Zone 5 Zone 4 Zone 3 Zone 2 Zone 1 0 1 1 1 1 1 1 1 E</Text><Text id="89571" page="5">Description Specification Comment Num- ber Do/Di ratio 1.5 Number 1 pair, length 40 D (incl. screw shaft and screw tip) 5D barrel length - 11.85 Screw elements diameter [mm] - Screw configuration Modular, tailor made for customer process - Material screw elements 1.4112, hardened R a ≤ 0,8 µm (resp. R z ≤ 4) - Material kneading blocks 1.4112, hardened R a ≤ 0,8 µm (resp. R z ≤ 4) - 11.70 Kneading element diame- ter [mm] - Material Distance element 1.4112, hardened R a ≤ 0,8 µm (resp. R z ≤ 4) - Screw tips Conical - Material screw tips 1.4112, hardened R a ≤ 0,8 µm (resp. R z ≤ 4) - Max. torque [Nm] 20 - Screw shaft sealing 3-times PTFE ring seal - Screw shaft 30 ° (DIN 5480) - Material screw shaft 1.4548</Text><Text id="89572" page="5">Description Specification Comment Num- ber - -- Extruder ZSE12 HP-PH Co-rotating twin screw extruder 50 – 2000 g/h (depends on the prod- uct) Hot melt extrusion T ≤ 250 °C</Text><Text id="89573" page="5">Drawing Num- ber --</Text><Text id="89575" page="6">Description Specification Comment Num- ber - Number 8 Zones compact barrel that can be split hori- zontally over the whole process length installed in a C-Profile - Design HP-bore whole 12,0 mm (H8) 5 x screw diameter (60 mm) - Zone 1: open, feed port Closed insert top Zone 2: open Closed insert top Zone 3: open Insert with bore top Zone 4: open Zone configuration Closed insert top Zone 5: open Closed insert top Zone 6: open Closed insert top, venting Zone 7: open Including closure Zone 8: closed - Material closing inserts for opened zones 1.4112 R a ≤ 0,8 µm (resp. R z ≤ 4) - Material feed port 1.4404 R a ≤ 0,8 µm (resp. R z ≤ 4) - Material closure caps with UNF bore 1.4112 R a ≤ 0,8 µm (resp. R z ≤ 4) Material injection nozzle - 1.4112 R a ≤ 0,8 µm (resp. R z ≤ 4) Seals with product contact - PTFE, at least FDA / EU conform incl. certificate Temperature * Because of heat transfer between barrels the control accuracy of ± 2 °C cannot be guaranteed at temperature delta Δ T ≥ 60 °C. Zone 1: 20-80 °C Zone 2: 20-160 °C* Zone 3-8: 20-250 °C accuracy of control ± 2°C - Each zone is temperature controlled (please refer to sensors) - Temperature / heating 2 heating cartridges in each barrel (265 W) - Temperature / Cooling Zone 1: connected to cooling water supply Zone 2-8: connected to cooling water supply RX9100 - Material barrel 1.4112 R a ≤ 0,8 µm (resp. R z ≤ 4) Extrusion height 1050 mm -</Text><Text id="89576" page="6">Drawing Num- ber --</Text><Text id="89578" page="7">Description Specification Comment Num- ber Connection - TC DIN DN 25 DIN 32676 Reihe A Seals with product contact - PTFE, FDA / EU conform incl. certifi- cate</Text><Text id="89579" page="7">Description Specification Comment Num- ber Design - Die with integrated material outlet and with bore holes for melt temper- ature and melt pressure sensor - Temperature Zone 9: 20-250 °C accuracy of control ± 10°C - Zone is temperature controlled (please refer to sensors) - Temperature / heating 1 heating cartridge 100W - Temperature / Cooling Not connected to cooling water - Material 1.4112 R a ≤ 0,8 µm (resp. R z ≤ 4) - whole size of die Available sizes: 3.0 mm 2.5 mm 2.0 mm 1.8 mm 1.5 mm 1.2 mm 1.0 mm 0.8 mm 0.5 mm</Text><Text id="89581" page="8">Description Specification Comment Num- ber PT100, class A - Temperature sensor cylin- der (no product contact) - No certificated factory calibration available Integrated in cartridge heater - PT 100 class A - Melt temperature (prod- uct contact) certificate factory calibration available - 2.4819 / HAS.C276 Measuring tip has contact to the product</Text><Text id="89582" page="8">Description Specification Comment Num- ber No active cooling Cooling cover 40D - 1.4301, polished with grain size 240 or better Frame - 1.4301, polished with grain size 240 or better movable, 4 wheels, lockable -</Text><Text id="89583" page="8">Description Specification Comment Num- ber Motor 2.8 kW 2000 rpm - I = 2.5 Gear 10 – 1000 rpm - Frequency converter rotary encoder - Cooling Water cooling System of protection IP 64 (motor) - Gearbox - Safety clutch between motor and gear, automatic overload and under- load monitoring and shutdown - Lubrication Optileb GT 220 (H1 NSF No. 134148) Transmission ratio i = 2.5 - - Material motor and gear box Painted with steel it, Installed in technical area</Text><Text id="89585" page="9">Description Specification Comment Num- ber At base frame Supply Main switch - Control cabinet Integrated into the frame</Text><Text id="89586" page="9">Description Specification Comment Num- ber General design - Easy to access / to clean / to disinfect Low dead space Pipes and electric wire behind a cover - Surface (without product contact) Easy to clean Ra ≤ 1,6 µm Labelling - Sensors, pipes, wire, equipment is la- belled according to PID Extruder measurements 1600 (H) x 1200 (B) x 900 (T) Without peripherals Weight ~ 350 kg - - Design connectors GMP-Design Self-closing and quick disconnect couplings used for the cooling system Or if necessary TC-connectors DIN 32676 or Inch BS 4825, reducing dif- ferent pipe classes Lubricants NSF H1 certified All used lubricants will be documented in a list during FAT</Text><Text id="89587" page="9">Description Specification Comment Num- ber - Melt pressure (product contact) diaphragm seal, 0 – 200 bar Performance level C ½“-20 UNF - 1.4545 with GTP+ coating GTP+ is a special coating from Gefran</Text><Text id="89589" page="10">Description Specification Comment Num- ber In addition to main guide lines for CE certificate DIN EN ISO 13850 DIN EN ISO 13849 parts 1 and 2 DIN EN 1037 DIN EN 61000-6-4, 6-2 Confirm to EN 60204 / DIN VDE 0113 part 1 DIN EN 60529 EMC 2014/30/EU Emergency stop Emergency One switch at panel - technology area Similar to IP 54 No verification available / possible Please refer to HDS, SDS - Panel, visualization, pro- gramming</Text><Text id="89591" page="11">Description Specification Comment Num- ber - -- Information Brabender (DDW-)MT‐S HD 1.0 - Technical features • Output depends on screws, Possi- ble types: TC1212 (coarse screw), TC1204 (fine screw) • 1.0 dm3 • volumetric feeding • two feeding screw • horizontal agitator - Integration in extruder line • Mounted on the extruder base frame. • The plug is connected behind the motor / gear technical area of the extruder. • Power supply from extruder - Surfaces with Product con- tact Metallic parts AISI 316L, R a ≤ 0,8 µm 2.2 certificate or better FDA/EU-Declaration of compliance for non-metallic material - HMI • Optional: Own operating panel • Feeder is controlled via the HMI of the extruder Signals to extruder HMI • Profinet connection • Run / stop • General alarm • Setpoint • Actual speed value</Text><Text id="89592" page="11">Drawing Num- ber --</Text><Text id="89594" page="12">Description Specification Comment Num- ber - -- Heating / Cooling unit BR‐018‐H1‐K12‐AE-FDA - Technical features heat 1,5kW, cool 12kW max. 27 l/min, max. 4,5 bar - Integration in extruder line • Mounted on a profile attached to the extruder frame. • The plug is connected on the motor side of the extruder. • Power supply from extruder - - Surfaces with Product con- tact - HMI with integrated local user interface Signals to extruder HMI • Profinet connection • Run / stop • General alarm • Setpoint • Actual temperature value</Text><Text id="89595" page="12">Drawing Num- ber --</Text><Text id="89597" page="13">Description Specification Comment Num- ber - -- Watson Marlow tube case pump 120U/DV 0.1-200 rpm With pump head 114DV (flip-top sin- gle-channel pump head for continu- ous tubing): 0.002 ml/min - 190 ml/min - Technical features Brushless DC motor Max. operating pressure: 2 bar Auto variable speed, variable speed 0.1rpm increments Analogue speed input; 4-20mA, 0-10V Tacho speed output; 0-5V - Integration in extruder line • Mounted on the extruder base frame. • The plug is connected behind the motor / gear technical area of the extruder. • Power supply from extruder tubing Surfaces with Product con- tact Smooth, wipe down case with no sharp edges to tear gloves and no bug traps. IP31 ingress protection HMI with integrated local keypad For remote and analogue control Signals to extruder HMI • 4-20 mA connection • Run / stop • Auto/Manuell • General alarm • Setpoint • Actual speed value</Text><Text id="89598" page="13">Drawing Num- ber --</Text><Text id="89600" page="14">Description Specification Comment Num- ber - -- MFB18-24VDC-BLE2-50.5- 500-SPEZ Length 500 mm Belt width 45 mm - Technical features 1-9.5 m/min Steady running No protective hood - Integration in extruder line • is mounted on a table/profile, which is mounted on the extruder frame; the plug is connected to the plug panel on the outlet side. • Power supply from extruder - Surfaces with Product con- tact FDA/EU-Declaration of compliance for non-metallic material and lubricants - HMI Cooling belt is controlled via the HMI of the extruder; no own display Signals to extruder HMI • Frequency converter to ET200 • Run / stop • General alarm frequency converter • Setpoint Actual speed value</Text><Text id="89601" page="14">Drawing Num- ber --</Text><Text id="89603" page="15">Description Specification Comment Num- ber - -- IPS-SG-E MINI PHARMA Throughput 4-15 kg/h Strand speed range 1-15 m/min Number of strands 1-3 - Technical features Feed height ~ 1050 mm Outlet height ~ 800 mm 1-3 Strands Integration in extruder line • The device is freestanding; the plug is connected to the plug panel on the outlet side. • Power supply from extruder - Cutting section Housing Bed knife complete with cutting holder, cutting blade with 4 cutting edges, cutting gap is easily adjustable 1 cylindrical cutting rotor, 6 teeth Cutting width 0,04-0,06 mm - Draw-in section Throat width 2,5 mm - Surfaces with Product con- tact Metallic parts 1.4112, 1.4571 or equal FDA/EU-Declaration of compliance for non-metallic material and lubricants No HMI HMI Pelletizer is controlled via the HMI of the extruder; no own display Signals to extruder HMI • Frequency converter to ET200 • Run / stop • General alarm frequency converter • Setpoint infeed roll and cutting • Actual speed value infeed roll and cutting</Text><Text id="89604" page="15">Drawing Num- ber --</Text><Text id="89606" page="16">Description Specification Comment Num- ber - -- Longer tube case pump (Drifton) L100-1S-2 0.01-10 rpm, 10.0-100.0 With pump head DMD15-13-B (single- channel pump head for continuous tubing, 2x3 rollers): 2 µl - 375 ml/min - Technical features Stepper motor Auto variable speed, variable speed 0.01 / 0.1rpm increments - Integration in extruder line • Mounted on the extruder base frame. • The plug is connected behind the motor / gear technical area of the extruder. • Power supply from extruder Silicone tubing Surfaces with Product con- tact Smooth, wipe down case with no sharp edges to tear gloves and no bug traps. IP31 ingress protection HMI with integrated local keypad (LCD) For remote and analogue control Signals to extruder HMI To be defined; not integrated in standard software until now</Text><Text id="89607" page="16">Drawing Num- ber --</Text><Text id="89609" page="17">Description Specification Comment Num- ber - -- CCR-10/06, BBA 0-1.9 rpm - Technical features Motor: 50 Hz; 1430 rpm; i=97.76:1 gear: i=15.5:1 - Integration in extruder line • is mounted on a table/profile, which is mounted on the extruder frame; the plug is connected to the plug panel on the outlet side. OR • Is mounted on a movable frame, which can be fixed at the extruder so that the complete extrusion line is movable. • Power supply from extruder - Surfaces with Product con- tact Metallic parts AISI 316L, R a ≤ 0,8 µm 2.2 certificate or better FDA/EU-Declaration of compliance for non-metallic material - HMI Cooling belt is controlled via the HMI of the extruder; no own display - Signals to extruder HMI • Frequency converter to ET200 • Run / stop • General alarm frequency converter • Setpoint speed • Actual speed value</Text><Text id="89610" page="17">Drawing Num- ber --</Text><Text id="89612" page="18">Abkürzung Beschreibung ATEX ATmosphères Explosibles DS Design Specification FDA U.S. Food &amp; Drug Administration</Text><Text id="89613" page="18">Description Specification Comment Num- ber - Room Minimum height 3 m Please refer to layout diagram - ATEX Not intended for use in ATEX zone - Underground (concrete) Compressive strength of foundation min. 200 kN/m 2 concrete quality B25 or better</Text><Text id="89614" page="18">Description Specification Comment Num- ber - Calibration NO factory calibration certificate for temperature sensor cylinder and drive available! The cylinder / barrel temperature sen- sors will be checked (in house calibra- tion) through FAT for at least two set points. - Factory Calibration certificate from the manufacturer for melt pressure and melt temperature available. 3.1 certificate not available Surfaces with product con- tact EN 10204 factory certificate 2.2 for material and surfaces extruder and a list with all areas with product contact will be provided EN 10204 Certificate of Compliance with the Order 2.1 for melt pressure - FDA/EU conformity (at least) for gas- kets / nonmetallic surfaces No conformity - Surfaces with no product contact - Lubricants NSF H1 conformity</Text><Text id="89616" page="19">Document Number Version Title BZ 40136146PI010 A PID Extruder N 40136146-01 01 Order confirmation</Text><Text id="89617" page="19">Abkürzung Beschreibung GMP Good manufacturing practice HDS Hardware Design Specification HMI Human machine interface IP IP code Protection class NSF National Sanitation Foundation PID Piping and Instrumentation Diagram PTFE Polytetrafluorethylen SDS Software Design Specification TC TriClamp UNF Unified National Fine Thread</Text></Spec>